What is the meaning of the red knob on the rotor lid?

A fixed-angle rotor with a red knob on the rotor lid indicates aerosol-tightness.

How did you manage to make the device so quiet?

The Centrifuge 5418 has an inner centrifuge lid which reduces the noise emission to a low level.

Which material is the inner centrifuge lid made of?

The inner lid of the Centrifuge 5418 is made of high-quality V2A stainless steel.

Can the Centrifuge 5418/ 5418 R be opened in case of a power failure?

Yes, the device has an emergency lid release. Before opening the centrifuge, pull the power plug and wait until the rotor stops spinning. The centrifuge 5418 has an emergency lid release via a cord that is located on the underside of the device in the base plate. Remove the white plastic cap and pull the cord downwards. The centrifuge 5418 R has an emergency lid release behind a plastic cover on the right side of the device. Rotate the plastic cover counterclockwise and remove it. Enter the centrifuge rotor key into the hexagonal opening at rear until some resistance can be felt. Slightly press and turn the rotor key counterclockwise.

How can the Centrifuge 5418/5418R be cleaned?

The Centrifuge 5418/5418 R can be cleaned with neutral detergents. For disinfection, we recommend alcohol or alcoholic disinfectants. Make sure that the relevant legal requirements and directives are observed when choosing the disinfection method. A detailed description can be found in the operating manual, which can be downloaded from our website.

What is the minimum selectable rotational speed of the Centrifuge 5418/5418 R?

The minimum selectable speed is 100 rpm. This is equivalent to an rcf of approx. 1 x g.

In which increments can the rotational speed/g-force be adjusted?

The rotational speed can be adjusted in increments of 100 rpm, the g-force (rcf) can be adjusted in increments of 100 x g.

In which increments can the time be adjusted?

In the centrifuge 5418, for a run time up to 10 min the increments are 0.5 min steps, after that it is set in increments of 1 min up to 9:59 h. The function for continuous run mode can be found above 9:59 h and below 0.5 min The symbol "oo" is displayed to indicate the continuous run. In the centrifuge 5418 R, for a run time up to 10 min the increments are 0.5 min steps, after that it is set in increments of 1 min up to 99 min. The function for continuous run mode can be found above 99 min and below 0.5 min. The symbol "oo" is displayed to indicate the continuous run.

My Centrifuge 5418 displays "EP". What does that mean?

"EP" is displayed when the automatic standby function is active. It is not an error code. If the centrifuge remains unused for more than 15 min., the standby function is activated, indicated by "EP" on the display. By using any key or knob or closing the centrifuge lid, the centrifuge is re-activated and ready to use. The letters "EP" were chosen because a lot of Eppendorf products already have this prefix in their name.

Can the fixed-angle rotor FA-45-18-11 be operated without a rotor lid?

The fixed-angle rotor FA-45-18-11 can be used with or without rotor lid. With rotor lid the centrifugation is aerosol-tight and the Centrifuge 5418/5418 R is even quieter. The aerosol-tight centrifugation can only be carried out with the rotor lid. Especially when working with pathogenic microorganisms, we recommend the usage of the aerosol-tight lid. When centrifuging filter devices like spin columns or other comparable tubes, the aerosol-tight rotor lid must be used in any case. This protects the centrifuge from damage – e. g. by torn-off tube lids.

Which material is the fixed-angle rotor for tubes made of?

The fixed-angle rotor is made of massive, anodized aluminum. This material is durable and has got a good chemical resistance. The rotor lid is made of the same material.

Can the sealing of the aerosol-tight rotor FA-45-18-11 be exchanged?

The sealing of the aerosol-tight rotor FA-45-18-11 can very easily be exchanged. A detailed description with illustrations can be found in the operating manual, which can be downloaded from our website.

Which tubes can be used in the Centrifuge 5418/5418 R?

1.5 ml and 2.0 ml Eppendorf ® tubes can be spun in the Centrifuge 5418/5418 R. With the help of adapters, the centrifugation of 0.2 ml PCR tubes, 0.6 ml Microtainer, 0.5 ml and 0.4 ml micro tubes is also possible. Even so-called spin columns (e.g. Quiagen, Macherey-Nagel, Vivascience) can be centrifuged. For centrifugation of spin columns, the rotor lid must be used.

For which applications can I use the Centrifuge 5418/ 5418 R?

The rotor of the Centrifuge 5418/5418 R allows a broad variety of applications. Up to 18 micro test tubes can be centrifuged at 16,873 x g. It can be used with tubes from 0.2 up to 2.0 ml. The potential applications include: - Isolation of DNA, RNA and proteins - Spin columns - Aerosol-tight centrifugation of infectious samples - Pelletizing of cells (bacteria, eukaryotic cells) up to 2.0 ml - Spinning down of PCR mixtures in tubes

In which rotors can I centrifuge 0.2 mL PCR tubes?

0.2 mL PCR tubes can be used in the rotor FA-45-18-11 using an adapter (Order No. International 5425 715.005; North America 022636260).

In which rotors can I centrifuge 0.5 mL micro test tubes?

0.5 mL micro test tubes can be centrifuged in the rotor FA-45-18-11 using an adapter (Order No. International 5425 716.001; North America 022636227).

How do I recognize aerosol-tight rotors?

Firstly, the aerosol-tight rotors can be recognized by their designation abbreviation “FA”, where the letter “A” indicates the aerosol tightness; secondly, we have color-coded the aerosol-tight rotors. All aerosol-tight rotors now have a red rotor lid screw, and a red ring is printed on to the rotor shaft.

Why are the standard rotors in the micro centrifuges 5418, 5418 R, 5424, 5424 R, 5430, and 5430 R aerosol-tight?

At Eppendorf, the safety of the user always has the highest priority. That is why we now fit our centrifuges with aerosol-tight rotors as standard – at no extra charge.

When does the opening of the centrifuge lid take place automatically or manually?

Following the end of a centrifuge run, only the lid of the Centrifuge 5418 is automatically opened in order to provide quicker access to the sample and to avoid potential heat accumulation. The Centrifuge 5418 R is not equipped with the automatic opening of the centrifuge lid. In order to maintain a consistent temperature in the rotor chamber and in the sample, the centrifuge lid for this device must always be manually opened by pressing the "open" key.

Can the Centrifuge 5418/5418 R be operated in the cooling room at 4° C?

The Centrifuge 5418 can be operated at an ambient temperature in the range from 2° C to 40° C. Operation in the cooling room at a temperature of 4° C is therefore possible. The permitted range of the ambient temperature is between 15 °C and 35 °C for the Centrifuge 5418 R, so that this centrifuge could not be operated in a cooling room at 4 °C.

What is "Fast Temp" (Centrifuge 5418 R)?

The "Fast Temp" function is a temperature control run of the Centrifuge 5418 R without samples and with a rotor and temperature-specific rotational speed in order to quickly bring the rotor chamber, incl. the rotor, buckets and adapters, to the set nominal temperature. In order that the samples can be centrifuged from the beginning on at the desired temperature, one starts this temperature control run during sample preparation by pressing the "Fast Temp" key. The display shows the current temperature and g force (rcf) or speed (rpm) as well as “FT” as symbol for a “Fast Temp” temperature run. You can find a more detailed description in the operating manual of the Centrifuge 5418/5418 R.

For the 5418 R, when does the continuous cooling of the rotor chamber start?

The continuous cooling starts with each rotor standstill of the Centrifuge 5418 R in order to maintain the preselected nominal temperature of the rotor chamber not only during centrifugation. To this purpose the following prerequisites must be met: - The centrifuge is switched on. - The centrifuge lid is closed. - The nominal temperature is lower than the ambient temperature. Continuous cooling is ended by opening the centrifuge lid.

What is the lowest temperature that can be reached with the Centrifuge 5418 R?

The lowest temperature of the Centrifuge 5418 R is 0 °C. The device is thereby optimized with the rotor in such a way that at least 4 °C is maintained at the maximum speed.

What is the temperature range of the Centrifuge 5418 R?

With the Centrifuge 5418 R it is possible to set the temperature within a range from 0 °C to +40 °C.

Does the Centrifuge 5418 R has an energy saving function?

Yes, the ECO shut-off automatically switchs off the compressor after 8 hours of non-use.

How can the speed display be switched from rotational speed (rpm) to relative centrifugal force (rcf, g-force)?

The display is switched back and forth between rpm and rcf by pressing the "rpm/rcf" key.

Does the lid latch have to be serviced or greased at regular intervals?

No, in order to ensure the full functionality of the lid latch, it must not be cleaned or greased. If you feel that this is nevertheless necessary, please contact our Technical Service. The contact address can be found in the operating manual of your centrifuge.

For what applications are aerosol-tight rotors important?

Aerosol-tight rotors are always recommended or even prescribed when working with hazardous or potentially hazardous substances. These can, for example, be viruses, pathogenic bacteria, potentially infectious blood samples or radioactive sample material.

Why are the standard rotors in the micro centrifuges 5418 R, 5420, 5424 R, 5425, 5427 R, 5430 and 5430 R aerosol-tight?

At Eppendorf, the safety of the user always has the highest priority. That is why we now fit our centrifuges with aerosol-tight rotors as standard – at no extra charge.

text.skipToContent text.skipToNavigation

JP | JPY

結果がありません

検索の提案

製品群

Show all Product Families ()

商品番号

Show all Articles ()

コンテンツ

Show all Content ()

Centrifuge 5418 R

Centrifuge Rotor FA-45-18-11 – QuickLock® mechanism

Soft-touch lid closure on the microcentrifuge Centrifuge 5418 R

Eppendorf microcentrifuge Rotor FA-45-18-11 for Centrifuge 5418 R with lid

製品情報

は、1.5/2.0Centrifuge 5418 RmLのチューブおよびMicrotainer^®の低容量から中容量用に特別に設計された18本架の微量遠心機です。最大速度16,873 × gは標準分子生物学の用途を可能にします。

製品情報をもっと見る

デモの依頼

追加でダウンロードできる材料がありますこのページの最後に

Sets & Bundles (1)

Services (13)

ローター (1)

アクセサリー (1)

1 Sets & Bundles

Centrifuge 5418 R

ダイヤル, 冷却付, Rotor FA-45-18-11付き（蓋付き）
100 V/50 – 60 Hz (JP)

製品のさらなる情報

カタログ番号 5401000030

製品をもっと見せる

お客様のショッピングカートに追加されました。

製品情報

テクニカルデータ

特徴

18本架容量があるローター搭載で冷蔵式、Centrifuge 5418 R1.5/2.0 mL ューブやMicrotainer^®の低容量から中程度の容量向けにデザインされています。最大速度16,873x × gは標準分子生物学の用途を可能にします。さらに、このコンパクトなデバイスはアクセス高が特に低く、非常に静かな動作を特徴としています。

Eppendorf QuickLock^®人間工学に基づいた操作ができるカバー

独自のQuickLockカバー付き遠心機ローター — 迅速かつ確実な1/4回転ロック式カバー。ウィルス、病原菌、血液サンプル、放射性サンプル等の有害なサンプルを安全に遠心分離エアロゾル密閉ローター。

あなたはEppendorf製品の誇り高い所有者ですか？すでに登録していますか？
Eppendorf製品を私たちに登録すると、次のものが得られることをご存知ですか？
• 100 epPoints^®の引換（登録した製品ごと）は、リワードショップで利用できます。
• 遠心機、シェーカー、CO2インキュベーター、またはサイクラーを登録すると、さらに3か月の保証が受けられます。
• Eppendorf限定の抽選へのエントリー（登録した製品ごとに）
• EppendorfのWebに投稿されるあなたの個人的な製品ストーリーを共有してください。

始めるのはとても簡単です！方法：
1. Eppendorf Appをダウンロードし、スキャンして登録します。
2. 弊社のWebページにアクセスし、myEppendorfアカウントにログオンして、製品のシリアル番号を入力します。
詳細は次をご参照ください：www.eppendorf.com/productregistration

End-of-Life

（寿命の終わり）梱包材の廃棄
フリーザーの梱包材には、木製パレット、段ボール、プラスチック製のダストカバー、発泡部品など、さまざまな素材が使われています。材料のリサイクルは日々ますます重要になっています：ヨーロッパでは、段ボール材料のほぼ100％がリサイクルされていることをご存知ですか？当社のフリーザー包装用段ボールの材料は、約50%リサイクル材料で構成されています。フリーザー段ボールの梱包材も収集し、組織の適切な収集コンテナーに廃棄することにより、貴重な原料をリサイクルするグローバルな持続可能性イニシアチブをサポートしてください。LD-PE製のプラスチック製ダストカバーと発泡部品に関しては、PE材料をリサイクルできる専用のリサイクルパートナーを選択することをお勧めします。利用可能なリサイクルオプションについては、地元の廃棄物処理業者または施設管理チームにお問い合わせいただくことをお勧めします。

装置の廃棄
当社のフリーザーは何年も使用可能ですが、交換が必要になった場合には、地域の要件に従って廃棄するようお願いします。積極的に冷却する装置の経験を持つ、認定された地元のリサイクルパートナーを強くお勧めします。「地元」で処理することは輸送の負荷を軽減します。また、冷却液を安全かつ持続的に除去およびリサイクルすることは、「認証」という点でも推奨されています。

除染
この機器は、で、あるいは生物学的の取り扱いのために使用されました。処分すべき装置の汚染を適切に除去してください。地域の要件を確認してください。詳細については、地域のバイオセーフティ担当者や廃棄物担当者にお問い合わせください。地域のリサイクル業者に特別な指示や文書化要件があるか確認してください。Eppendorf除染フォームシートを参考として使用できます。

読む量をもっと少なくする

仕様	5418 R

最大 RCF	16873 × g
最大固定角ロータ付きのRCF	16873 × g
速度	100 – 14,000 rpm (100 rpm ステップ)
製品タイプ	遠心機
利用可能なローター	1
最大容量	18 × 1.5/2.0 mL
加速時間¹⁾	13 s
減速時間¹⁾	13 s
タイマー	30 秒～9:59 時間、連続動作機能付き
ノイズレベル	< 57 dB(A)
電源	100 V, 50 – 60 Hz
最大電力消費	320 W
寸法（W × D × H）	30 × 46 × 25 cm / 11.7 × 18.23 × 9.8 in
製品の重量	22 kg / 48.5 lb
高さ(蓋開放)	52 cm / 20 in
冷却	冷却付
温度範囲	0 °C ～ +40 °C