What is the meaning of the red knob on the rotor lid?

A fixed-angle rotor with a red knob on the rotor lid indicates aerosol-tightness.

How did you manage to make the device so quiet?

The Centrifuge 5418 has an inner centrifuge lid which reduces the noise emission to a low level.

Which material is the inner centrifuge lid made of?

The inner lid of the Centrifuge 5418 is made of high-quality V2A stainless steel.

Can the Centrifuge 5418/ 5418 R be opened in case of a power failure?

Yes, the device has an emergency lid release. Before opening the centrifuge, pull the power plug and wait until the rotor stops spinning. The centrifuge 5418 has an emergency lid release via a cord that is located on the underside of the device in the base plate. Remove the white plastic cap and pull the cord downwards. The centrifuge 5418 R has an emergency lid release behind a plastic cover on the right side of the device. Rotate the plastic cover counterclockwise and remove it. Enter the centrifuge rotor key into the hexagonal opening at rear until some resistance can be felt. Slightly press and turn the rotor key counterclockwise.

How can the Centrifuge 5418/5418R be cleaned?

The Centrifuge 5418/5418 R can be cleaned with neutral detergents. For disinfection, we recommend alcohol or alcoholic disinfectants. Make sure that the relevant legal requirements and directives are observed when choosing the disinfection method. A detailed description can be found in the operating manual, which can be downloaded from our website.

What is the minimum selectable rotational speed of the Centrifuge 5418/5418 R?

The minimum selectable speed is 100 rpm. This is equivalent to an rcf of approx. 1 x g.

In which increments can the rotational speed/g-force be adjusted?

The rotational speed can be adjusted in increments of 100 rpm, the g-force (rcf) can be adjusted in increments of 100 x g.

In which increments can the time be adjusted?

In the centrifuge 5418, for a run time up to 10 min the increments are 0.5 min steps, after that it is set in increments of 1 min up to 9:59 h. The function for continuous run mode can be found above 9:59 h and below 0.5 min The symbol "oo" is displayed to indicate the continuous run. In the centrifuge 5418 R, for a run time up to 10 min the increments are 0.5 min steps, after that it is set in increments of 1 min up to 99 min. The function for continuous run mode can be found above 99 min and below 0.5 min. The symbol "oo" is displayed to indicate the continuous run.

My Centrifuge 5418 displays "EP". What does that mean?

"EP" is displayed when the automatic standby function is active. It is not an error code. If the centrifuge remains unused for more than 15 min., the standby function is activated, indicated by "EP" on the display. By using any key or knob or closing the centrifuge lid, the centrifuge is re-activated and ready to use. The letters "EP" were chosen because a lot of Eppendorf products already have this prefix in their name.

Can the fixed-angle rotor FA-45-18-11 be operated without a rotor lid?

The fixed-angle rotor FA-45-18-11 can be used with or without rotor lid. With rotor lid the centrifugation is aerosol-tight and the Centrifuge 5418/5418 R is even quieter. The aerosol-tight centrifugation can only be carried out with the rotor lid. Especially when working with pathogenic microorganisms, we recommend the usage of the aerosol-tight lid. When centrifuging filter devices like spin columns or other comparable tubes, the aerosol-tight rotor lid must be used in any case. This protects the centrifuge from damage – e. g. by torn-off tube lids.

Which material is the fixed-angle rotor for tubes made of?

The fixed-angle rotor is made of massive, anodized aluminum. This material is durable and has got a good chemical resistance. The rotor lid is made of the same material.

Can the sealing of the aerosol-tight rotor FA-45-18-11 be exchanged?

The sealing of the aerosol-tight rotor FA-45-18-11 can very easily be exchanged. A detailed description with illustrations can be found in the operating manual, which can be downloaded from our website.

Which tubes can be used in the Centrifuge 5418/5418 R?

1.5 ml and 2.0 ml Eppendorf ® tubes can be spun in the Centrifuge 5418/5418 R. With the help of adapters, the centrifugation of 0.2 ml PCR tubes, 0.6 ml Microtainer, 0.5 ml and 0.4 ml micro tubes is also possible. Even so-called spin columns (e.g. Quiagen, Macherey-Nagel, Vivascience) can be centrifuged. For centrifugation of spin columns, the rotor lid must be used.

For which applications can I use the Centrifuge 5418/ 5418 R?

The rotor of the Centrifuge 5418/5418 R allows a broad variety of applications. Up to 18 micro test tubes can be centrifuged at 16,873 x g. It can be used with tubes from 0.2 up to 2.0 ml. The potential applications include: - Isolation of DNA, RNA and proteins - Spin columns - Aerosol-tight centrifugation of infectious samples - Pelletizing of cells (bacteria, eukaryotic cells) up to 2.0 ml - Spinning down of PCR mixtures in tubes

In which rotors can I centrifuge 0.2 mL PCR tubes?

0.2 mL PCR tubes can be used in the rotor FA-45-18-11 using an adapter (Order No. International 5425 715.005; North America 022636260).

In which rotors can I centrifuge 0.5 mL micro test tubes?

0.5 mL micro test tubes can be centrifuged in the rotor FA-45-18-11 using an adapter (Order No. International 5425 716.001; North America 022636227).

How do I recognize aerosol-tight rotors?

Firstly, the aerosol-tight rotors can be recognized by their designation abbreviation “FA”, where the letter “A” indicates the aerosol tightness; secondly, we have color-coded the aerosol-tight rotors. All aerosol-tight rotors now have a red rotor lid screw, and a red ring is printed on to the rotor shaft.

Why are the standard rotors in the micro centrifuges 5418, 5418 R, 5424, 5424 R, 5430, and 5430 R aerosol-tight?

At Eppendorf, the safety of the user always has the highest priority. That is why we now fit our centrifuges with aerosol-tight rotors as standard – at no extra charge.

When does the opening of the centrifuge lid take place automatically or manually?

Following the end of a centrifuge run, only the lid of the Centrifuge 5418 is automatically opened in order to provide quicker access to the sample and to avoid potential heat accumulation. The Centrifuge 5418 R is not equipped with the automatic opening of the centrifuge lid. In order to maintain a consistent temperature in the rotor chamber and in the sample, the centrifuge lid for this device must always be manually opened by pressing the "open" key.

Can the Centrifuge 5418/5418 R be operated in the cooling room at 4° C?

The Centrifuge 5418 can be operated at an ambient temperature in the range from 2° C to 40° C. Operation in the cooling room at a temperature of 4° C is therefore possible. The permitted range of the ambient temperature is between 15 °C and 35 °C for the Centrifuge 5418 R, so that this centrifuge could not be operated in a cooling room at 4 °C.

What is "Fast Temp" (Centrifuge 5418 R)?

The "Fast Temp" function is a temperature control run of the Centrifuge 5418 R without samples and with a rotor and temperature-specific rotational speed in order to quickly bring the rotor chamber, incl. the rotor, buckets and adapters, to the set nominal temperature. In order that the samples can be centrifuged from the beginning on at the desired temperature, one starts this temperature control run during sample preparation by pressing the "Fast Temp" key. The display shows the current temperature and g force (rcf) or speed (rpm) as well as “FT” as symbol for a “Fast Temp” temperature run. You can find a more detailed description in the operating manual of the Centrifuge 5418/5418 R.

For the 5418 R, when does the continuous cooling of the rotor chamber start?

The continuous cooling starts with each rotor standstill of the Centrifuge 5418 R in order to maintain the preselected nominal temperature of the rotor chamber not only during centrifugation. To this purpose the following prerequisites must be met: - The centrifuge is switched on. - The centrifuge lid is closed. - The nominal temperature is lower than the ambient temperature. Continuous cooling is ended by opening the centrifuge lid.

What is the lowest temperature that can be reached with the Centrifuge 5418 R?

The lowest temperature of the Centrifuge 5418 R is 0 °C. The device is thereby optimized with the rotor in such a way that at least 4 °C is maintained at the maximum speed.

What is the temperature range of the Centrifuge 5418 R?

With the Centrifuge 5418 R it is possible to set the temperature within a range from 0 °C to +40 °C.

Does the Centrifuge 5418 R has an energy saving function?

Yes, the ECO shut-off automatically switchs off the compressor after 8 hours of non-use.

How can the speed display be switched from rotational speed (rpm) to relative centrifugal force (rcf, g-force)?

The display is switched back and forth between rpm and rcf by pressing the "rpm/rcf" key.

Does the lid latch have to be serviced or greased at regular intervals?

No, in order to ensure the full functionality of the lid latch, it must not be cleaned or greased. If you feel that this is nevertheless necessary, please contact our Technical Service. The contact address can be found in the operating manual of your centrifuge.

For what applications are aerosol-tight rotors important?

Aerosol-tight rotors are always recommended or even prescribed when working with hazardous or potentially hazardous substances. These can, for example, be viruses, pathogenic bacteria, potentially infectious blood samples or radioactive sample material.

Why are the standard rotors in the micro centrifuges 5418 R, 5420, 5424 R, 5425, 5427 R, 5430 and 5430 R aerosol-tight?

At Eppendorf, the safety of the user always has the highest priority. That is why we now fit our centrifuges with aerosol-tight rotors as standard – at no extra charge.

text.skipToContent text.skipToNavigation

KR | KRW

결과 없음

검색 제안

제품군

모든 제품군 표시 ()

기사

모든 기사 표시 ()

콘텐츠

모든 콘텐츠 표시 ()

Centrifuge 5418 R

Centrifuge Rotor FA-45-18-11 – QuickLock® mechanism

Soft-touch lid closure on the microcentrifuge Centrifuge 5418 R

Eppendorf microcentrifuge Rotor FA-45-18-11 for Centrifuge 5418 R with lid

제품 정보

Centrifuge 5418 R은 저용량에서 중간 용량의 1.5/2.0 mL tube 및 Microtainer^®를 위한 18홀 마이크로 원심분리기입니다. 최대 16,873 × g의 속도로 표준 분자생물학 실험에 적합합니다.

제품 정보 자세히 표시

데모 신청

이 페이지 하단에서 추가 다운로드 자료를찾을 수 있습니다.

세트 및 번들 (1)

Services (15)

로터 (1)

액세서리 (1)

1 세트 및 번들

Centrifuge 5418 R

로터리 버튼, 냉장, Rotor FA-45-18-11 및 로터 뚜껑 포함
230 V/50 – 60 Hz (EU)

추가 제품 정보...

수량

재고 확인

카탈로그 번호 5401000010

순 가격

₩ 8,690,000

총 가격

₩ 9,559,000

문의

더 많은 제품 표시

장바구니에 추가됨

제품 정보

기술 정보

특징

18홀 로터가 장착된 냉장 Centrifuge 5418 R은 중저용량의 1.5/2.0 mL 튜브와 Microtainer^®에 적합하게 설계되었습니다. 최대 속도가 16,873 × g이어서 표준 분자생물학 실험에 적합합니다. 또한 높이가 낮아 접근이 용이하고 놀라울 만치 조용한 작동이 특징입니다.

인체공학적인 작동을 위한 Eppendorf QuickLock^® 뚜껑

원심분리기 로터에 특수한 QuickLock 뚜껑을 사용해 1/4만 돌려 뚜껑을 빠르고 안전하게 잠글 수 있습니다. 바이러스, 병원균, 혈액 샘플, 방사성 프로브 등 위험 시료의 안전한 원심분리를 위해 Aerosol-tight 로터를 제공합니다.

Eppendorf 제품을 소유하고 계신가요? 이미 등록하셨나요?

Eppendorf 제품을 등록하면 다음과 같은 혜택이 제공된다는 사실을 알고 계셨나요?
• 리워드 샵에서 사용할 수 있는 100 epPoints^® 적립(등록 제품당)
• 원심분리기, Shaker, CO2 Incubator, Cycler 등록 시 3개월 보증 연장
• Eppendorf 경품 추첨 참여(등록 제품당)
• Eppendorf 웹 사이트에 제품 이용 사례 게시

지금 바로 등록하세요! 1. Eppendorf 앱을 다운로드한 후 스캔하여 등록하거나
2. 웹 페이지를 방문한 후 myEppendorf 계정에 로그인하여 제품 일련번호를 입력합니다.
추가 정보:www.eppendorf.com/productregistration

End-of-Life

포장재 폐기
원심분리기의 포장재에는 목재 파렛트, 판지, 플라스틱 먼지 커버, 폼 자재 등 다양한 자재가 포함됩니다. 이러한 자재의 재활용은 점점 더 중요해지고 있습니다. 유럽에서는 거의 모든 판지 자재가 재활용되고 있다는 사실을 아시나요? Eppendorf의 원심분리기 포장용 판지 자재는 약 50%가 재활용 자재입니다. Freezer 판지 포장재를 수거하여 회사에 비치되어 있는 수거함에 버림으로써 귀중한 원자재를 재활용하는 글로벌 지속 가능성 프로그램에 동참하시기 바랍니다. LD-PE 소재의 플라스틱 먼지 커버와 폼 자재의 경우 PE 자재를 재활용할 수 있는 재활용 협력업체를 선정할 것을 권장합니다. 내 회사에서 사용 가능한 재활용 옵션을 이해하려면 지역 폐기물 운송업체 또는 시설 관리팀에 문의하시기 바랍니다.

장비 폐기
Eppendorf의 원심분리기는 수년 동안 사용할 수 있지만, 교체해야 하는 경우 현지의 관련 폐기 요건을 충족해야 합니다. Eppendorf는 능동 냉각 기기에 관한 경험이 있는 인증된 현지 재활용 협력업체를 선정할 것을 권장합니다. 현지 업체를 활용하면 운송에 따른 환경 영향이 최소화됩니다. 냉장형 원심분리기인 경우 냉각액을 안전하고 지속 가능한 방식으로 제거 및 재활용하는 '인증된' 방식을 사용하시기 바랍니다.

오염 물질 제거
본 장비는 실험실에서 또는 생물학적 시료를 처리하는 용도로 사용되었습니다. 폐기할 장비에서 오염 물질을 적절하게 제거하십시오. 현지 요건을 확인하십시오. 자세한 내용은 지역 생물안전 담당자 및/또는 폐기물 담당자에게 문의하십시오. 지역 재활용 파트너에게 특별 지침 및/또는 문서화 요건이 있는지 확인하십시오. Eppendorf 오염 물질 제거 양식 시트를 참고할 수 있습니다.

간단히 보기

사양	5418 R

최대 RCF	16873 × g
최대 고정각 로터 사용 시 최대 RCF	16873 × g
속도	100 – 14,000 rpm (100 rpm 단계)
제품 유형	원심분리기
사용 가능한 로터	1
최대 용량	18 × 1.5/2.0 mL
가속 시간¹⁾	13 s
감속 시간¹⁾	13 s
타이머	30 s ~ 9:59 h, 연속 작동 가능
소음 레벨	< 57 dB(A)
전원공급장치	230 V, 50 – 60 Hz
최대 소비 전력	320 W
치수(W × D × H)	30 × 46 × 25 cm / 11.7 × 18.23 × 9.8 in
제품 무게	22 kg / 48.5 lb
높이(뚜껑 개방 시)	52 cm / 20 in
냉각	냉장
온도 범위	0 °C ~ +40 °C