Is it possible to operate the Centrifuge 5702 in the cooling room?

Yes, the Centrifuge 5702 may be operated in the cooling room. When moving the centrifuge from the cooling room to a normal lab room, the centrifuge must either run warm for half an hour in the cooling room or warm up for at least 3 hours in the lab room without being connected to the power supply. This is to avoid damage caused by condensation.

Is it possible to operate the Centrifuge 5702 R in the cooling room?

No, the Centrifuge 5702 R must not be operated in the cooling room. To avoid damage caused by condensation, the centrifuge should be operated in a normal lab room. To ensure optimum operation of the centrifuge, the ambient temperature should be between 10 °C and 40 °C. At temperatures below 18 °C, a warming-up time of approx. 1 hour is required to ensure faultless operation.

Which material is the rotor chamber made of?

The rotor chamber is made of high-quality steel.

How can the centrifuge be opened in the case of power failure?

1. Pull the plug and wait until the rotor comes to a standstill (can take up to 5 minutes!). 2. The emergency lid release is located on the bottom of the device: a small, white plastic button is located in the base plate in front of the front right device foot. Remove this and pull the cord vertically downwards. The lid will open. 3. Please ensure that the cord retracts completely into the housing when close the lid again. Press the plastic button back into the base plate.

What is the minimum selectable speed and in which increments can it be increased in centrifuge 5702/R/RH?

The minimum selectable speed is 100 rpm. It can be increased in increments of 100. The g-forces displayed are only approximations. The exact values can be calculated for the different adapters. Please bear in mind that a setting of 100 rpm equals a relative centrifugal force of 1.5 x g. The 100 x g displayed is only reached at a rotational speed of 800 rpm.

Is it possible that the time is counted down only after reaching the selected speed?

Yes, this is possible. Pressing the START/STOP key for longer than 2 s with the centrifuge lid open initiates the switch to the "at set rpm" mode, as symbolized by a pictogram. To exit the "at set rpm" mode again, press the START/STOP key again for longer than 2 s with the centrifuge lid open, until the pictogram appears.

Is it possible to switch off the signal tone?

Yes. If the OPEN key is pressed for longer than 2 s while the centrifuge lid is open, either “b on“ (signal tone on) or “b of“ (signal tone off) will appear. With the Centrifuges 5702 R / 5702 RH, a pictogram on the display indicates that the signal tone is switched on.

Is it also possible to adjust the parameters during centrifugation?

Adjustments to the time, rotational speed and temperature (5702 R / 5702 RH only) can be made while the centrifuge is running. To do this, press the SHORT key until the display begins to flash. You can now set the new centrifugation parameters using the TIME and SPEED dials and the TEMP keys. The new centrifugation parameters are taken over after 5 s.

Can the values set for routine applications be secured against unintentional adjustment?

Yes, with the Centrifuges 5702 / 5702 R / 5702 RH it is possible to fix the desired settings. To do this, press the SHORT and the OPEN keys simultaneously for at least 5 s while the centrifuge lid is open. In this way, the dial adjustment is deactivated and "lo on" will appear on the display of the Centrifuge 5702. On the display of the Centrifuges 5702 R / 5702 RH, the fixed setting of the centrifugation parameters will be indicated by an additional pictogram. The set values can now no longer be adjusted, irrespective of whether the centrifuge is running or not. In order to reactivate the dial adjustment, press the SHORT and OPEN keys again for 5 s. "lo of" will appear on the display of the Centrifuge 5702, and the pictogram on the display of the Centrifuges 5702 R / 5702 RH will change. The parameters can now be adjusted again.

How can the set parameters be saved using the program keys?

This is only possible when the centrifuge is not running. First, set the desired program parameters using the TIME and SPEED dials and the TEMP arrow keys. The "at set rpm" function and the slower acceleration and braking ramps can also be saved in the fixed programs, if required. Keep the PROG 1 or PROG 2 key pressed for 2 s until the program key stops flashing and glows continuously. A short signal tone will sound. The program has been saved.

Can the ShortSpin key be programmed?

No, the ShortSpin key cannot be programmed.

What are the maximum values for the acceleration and deceleration times?

The acceleration time to the maximum rotational speed is less than 25 s, the deceleration time from the maximum rotational speed is approx. 25 s.

Is it possible to change the acceleration and braking ramps for specific applications in centrifuge 5702/R/RH?

Yes, when working with Ficoll density gradients or other sensitive applications (e.g. certain blood and urea centrifugations), slower acceleration and braking ramps can be set for the Centrifuge 5702 / 5702 R / 5702 RH. This allows the centrifuge to accelerate and decelerate smoothly and ensures optimum centrifugation results. Press the SHORT key for more than 5 s while the centrifuge lid is open. The writing on the display changes from "br on" (brake on) to "br OF" (brake off), or "soft" is displayed (5702 R, 5702 RH). The slower acceleration and braking ramps are now activated. If the SHORT key is pressed for less than 5 s while the centrifuge lid is open, the current state is displayed.

Are any rotors for 1.5/ 2.0 mL micro test tubes or microplates available for Centrifuge 5702 / 5702 R / 5702 RH?

The centrifuge has a fixed-angle rotor for 1.5/ 2.0 mL micro test tubes. With the help of adapters, tubes with a volume of 0.2 - 0.6 mL can also be used. A rotor for microplates, however, is not available.

What is the maximum number of 15 mL conical tubes that can be centrifuged in the fixed-angle rotor F-35-30-17 of centrifuge 57xx?

A maximum of 20 x 15 mL conical tubes can be centrifuged in the fixed-angle rotor F-35-30-17.

Is aerosol-tight centrifugation possible in the Centrifuge 5702 / 5702 R / 5702 RH?

Yes, there are aerosol-tight caps available for the round buckets of the rotor A-4-38. These caps are certified according to Porton Down. All round bucket adapters, except for the adapter 5702 723.002, can be used for aerosol-tight centrifugation. Instead of the adapter 5702 723.002 for two 15 ml Falcon tubes each, the adapter 5702 732.001 for one 15 ml Falcon tube is available for aerosol-tight centrifugation.

How can the adapters and rotors of centrifuge 5702/R/RH be cleaned?

Rotors, buckets, sleeves and adapters should be cleaned on a monthly basis with a neutral detergent in order to prevent material changes due to residues of the material being centrifuged. Please do not use sodium hypochlorite or chlorous or oxidizing disinfectants and detergents under any circumstances. Disinfection with glutaraldehyde solution is possible. We recommend Cidex ® activated glutaraldehyde solution ( ® : Johnson & Johnson). Plastic adapters and rubber inlays are dishwasher safe.

Are the adapters and rotors of centrifuge 5702/R/RH autoclavable?

All rotors, buckets, adapters, sleeves and caps are autoclavable for 20 min. at 121°C. The rotors A-4-38 and F-35-30-17 as well as the affiliated buckets and sleeves can even be autoclaved for 2 hrs. at 140°C and 3 bar.

How can the relative centrifugal force (rcf) be determinedd for the different adapters?

The rcf (g-force) shown on the display is standardized for 15 mL Falcon tubes (rotor: A-4-38). The rcf to be attained at maximum speed for the various adapters are listed in the Operating Manual. In order to determine a specific rcf for a specific adapter, use the following formula according to DIN 58970: rcf = 1.118 · 10-5 · n2 · rmax n: rotational speed in rpm rmax: max. centrifugation radius in cm

Does the Centrifuge 5702 R/ RH has an energy saving function?

Yes, the ECO shut-off automatically switchs off the compressor after 8 hours of non-use. The device has a stand-by button.

How can I use BD vacutainer CPT tubes (16 x 125mm) in Eppendorf centrifuges 5702/5702R/5702RH?

You will need rotor A-4-38 (art.no. 5702 740.004) with 4 x bucket for 16 x 125mm round bottom tubes (art.no. 5702 764.000).

What is the maximum number of 15 mL conical tubes that can be centrifuged in the swing-bucket rotor A-4-38 of centrifuges 57xx?

Maximum capacity of the swing-bucket rotor A-4-38 is 8 x 15 mL conical tubes. Aerosol-tight centrifugation is only possible with 4 x 15 mL conical tubes in the swing-bucket rotor.

text.skipToContent text.skipToNavigation

DE | EUR

No results found

Search Suggestions

Product Families

Show all Product Families ()

Article

Show all Articles ()

Content

Show all Content ()

Centrifuge 5702/ 5702 R/5702 RH - Low-speed centrifugation

The low-speed centrifuge Centrifuge 5702 R is quiet and ergonomic

LCD display and rotary knob on the Centrifuge 5702 R

Centrifuge 5702, Rotor A-4-38, x-75 mL conical tubes

General Lab Product Version

IVD Product Version

Product Information

Are you looking to improve your work environment? The 5702 family of low-speed centrifuges, including the heated Centrifuge 5702 RH, are quiet in operation, compact in design and provide six different rotor options to accommodate any type of tube and requirement for low to mid-throughput applications in clinical research and cell culture.

Show more Product Information

Request a demo

You will find additional download material at the bottom of this page

Product Information

Technical Data

Applications

Features

Heated centrifuge and low-speed centrifugation

The 5702 family of low-speed centrifuges, including the heated centrifuge Eppendorf Centrifuge 5702 RH, was especially designed to meet the requirements of low- to mid-throughput clinical research and cell culture labs. These low-speed centrifugation devices are compact in design, fitting comfortably on every lab bench. They operate quietly, benefiting your work environment, and provide six different centrifuge rotor options to accommodate any type of tube.

Your lab centrifuge for low-speed

Make your lab environment a better place to work with the 5702 family of low-speed centrifuges that are quiet, user-friendly, and so compact that you can fit one comfortably on every lab bench. The low access height allows for simple loading and unloading of samples.

Eppendorf Centrifuge 5702 price and models

Within the 5702 family, we offer three different models to suit your lab or your application: Centrifuge 5702, which is suitable for standard applications; the refrigerated Centrifuge 5702 R for heat-sensitive samples; and the refrigerated and actively heated Centrifuge 5702 RH, which is well suited for working with living specimens, for example in cell culture. For prices please see the product overview above.

Temperature management

Choose the right model to meet your temperature requirements:
• Centrifuge 5702 – optimized air flow minimizes sample warming during run
• Centrifuge 5702 R/RH – FastTemp function for fast pre-cooling
• Centrifuge 5702 RH only – active heating guarantees high temperature accuracy during the entire centrifugation cycle
• Centrifuge 5702 R/RH – reduced energy consumption and extended compressor life thanks to the ECO shut-off that engages after a period of inactivity

Safety management

The 5702 family of low-speed centrifuges come with an easy to clean stainless steel rotor chamber. Automatic centrifuge rotor recognition and imbalance detection ensure operational safety, and a key lock prevents accidental parameter changes. Optional aerosol-tight caps are ready for you to use when working with hazardous samples.

Swing-bucket rotor A-4-38 with aerosol-tight caps

Proud owner of an Eppendorf product? Already registered?

Did you know that if you register your Eppendorf product, such as the Eppendorf Centrifuge 5702 or the Eppendorf Centrifuge 5702 R, with us you will get the following?
• 100 epPoints^® (for each product you register) to redeem in our rewards shop
• Additional 3 months warranty when you register a centrifuge, shaker, CO₂ incubator or cycler
• Entry in an exclusive Eppendorf prize draw (for each product you register)
• Get your personal product story to be posted on the Eppendorf website

Getting started is super easy! Either -
1. Download the Eppendorf App, scan and register OR
2. Visit our webpage, log onto your myEppendorf account and enter the product serial number
More information: www.eppendorf.link/product-registration

End-of-life

Disposal of packaging
The packaging of the Eppendorf Centrifuge 5702, Eppendorf Centrifuge 5702 R, or any other 5702 centrifuge contains different materials, this can include a wooden pallet, cardboard, a plastic dust cover, and some foam parts. Recycling of materials becomes more and more important every day: Are you aware that nearly all cardboard material is recycled in Europe? Our centrifuge packaging cardboard material consists of ca. 50% recycling material. Please support the global sustainability initiative of recycling valuable raw material by also collecting the freezer cardboard packaging material and disposing of it in the appropriate collection container at your organization. In respect to the plastic dust cover made of LD-PE and the foam parts, we recommend to select a dedicated recycling partner where PE material can be recycled. We suggest you contact your local waste hauler or facility management team to understand the available recycling options for your organization.

Disposal of instrument
Our centrifuges, including the heated centrifuge models last for many years, but if they need to be replaced, we kindly ask you to fulfill local requirements for disposal of these instruments. We strongly recommend a certified local recycling partner with experience in instruments with active cooling. Keeping it “local“ reduces the impact of transportation, and the "certified" aspect is recommended due to the safe and sustainable removal and recycling of the cooling liquids if it is a refrigerated centrifuge.

Decontamination
This piece of equipment was used in a laboratory and/ or was used to handle biological samples. Please keep in mind to adequately decontaminate the equipment which needs to be disposed. Check local requirements. For more information, get in contact with your local biosafety officer and/ or waste officer. Check if your local recycling partner has special instructions and/ or documentation requirements. You may also use the Eppendorf decontamination form sheet as guidance.

Read Less

Specifications	5702	5702 R	5702 RH

Max. RCF	3000 × g	3000 × g	3000 × g
Max. RCF with fixed-angle rotor	1900 × g	1900 × g	1900 × g
Max. RCF with swing-bucket rotor	3052 × g	3052 × g	3052 × g
Speed	100 – 4,400 rpm (100 rpm steps)	100 – 4,400 rpm (100 rpm steps)	100 – 4,400 rpm (100 rpm steps)
Product type	Centrifuges	Centrifuges	Centrifuges
Rotors available	6	6	6
Max. capacity	4 × 100 mL	4 × 100 mL	4 × 100 mL
Acceleration time¹⁾	≤19 s	≤20 s	≤19 s
Deceleration time¹⁾	≤19 s	≤28 s	≤29 s
Timer	0 – 99 min, with continuous run function	0 – 99 min, with continuous run function	0 – 99 min, with continuous run function
SOFT brake function	yes	yes	yes
Noise level	< 52 dB(A) with Rotor A-4-38	<46 dB(A) with Rotor A-4-38	<46 dB(A) with Rotor A-4-38
Power supply	230 V, 50 – 60 Hz	230 V, 50 – 60 Hz	230 V, 50 – 60 Hz
Max. power consumption	200 W	380 W	380 W
Dimensions (W × D × H)	32 × 40 × 24 cm / 12,6 × 15,6 × 9,6 in	38 × 58 × 27 cm / 15 × 22,9 × 10,6 in	38 × 58 × 27 cm / 15 × 22,9 × 10,6 in
Footprint (dimensions w/o front panel, WxD)	32 × 40 cm /  12.6 × 15.6 in	38 × 58 cm /  15 × 22.9 in	−
Product weight	19 kg / 41,9 lb	35 kg / 77,1 lb	35 kg / 77,1 lb
Height (with open lid)	53 cm / 20,7 in	60 cm / 23,4 in	60 cm / 23,4 in
Cooling	non-refrigerated	refrigerated	refrigerated/heated
Temperature range	–	-9 °C to 40 °C	-9 °C to 42 °C

Max. capacity
Conical tubes	20 × 15 mL/ 4 × 50 mL	20 × 15 mL/ 4 × 50 mL	20 × 15 mL/ 4 × 50 mL
Blood collection tubes	36 × 13 mm/ 30 × 16 mm	36 × 13 mm/ 30 × 16 mm	36 × 13 mm/ 30 × 16 mm