How does the shaker agitation rate and orbit affect culture growth?

Generally, agitation speed and orbit affect both the aeration and the mixing of the culture. Greater aeration increases oxygen transfer rate (OTR), boosting cell growth. The size of the orbit affects OTR linearly and the speed has a square-law relationship. Therefore, if the size of the orbit doubles, say from 1/2 to 1," the amount of OTR should double〖RPM〗_1/〖RPM〗_2 = (r_2^2)/(r_1^2 ), then 〖RPM〗_2 = √(〖RPM〗_1^2 (r_1/r_2 ) ). If the speed doubles, the OTR should quadruple. Of course, these are general rules and caution should be taken with shear sensitive cells. However, this information can be used to estimate the conditions needed to obtain the same results on different model shakers. For example, to get the same oxygen transfer in a shaker with a 1 in orbit running at 300 rpm, a shaker with 3/4 in orbit must be run at 350 rpm.

Do Eppendorf shakers come with platforms?

Each Eppendorf shaker is available with multiple platform options, which are ordered separately to give you the flexibility to choose the one that best suits your needs. Dedicated platforms include installed clamps of a single size (ie. only 250 mL clamps) and provide in most cases the best capacity but does not allow for the use of different size clamps or holders. Universal Platforms are designed for use with a combination of various-sized clamps and test tube racks providing maximum flexibility. When ordering a Universal Platform, clamps and test tube racks must also be ordered separately.

What is the temperature offset function?

The temperature offset function on many of our shakers allow you to match a reference point" temperature inside the chamber (culture medium) with the "Actual Value" displayed. The temperature offset function on Innova Incubated shakers allows you to monitor the temperature of the media providing you a clearer and more accurate picture. Please be aware that matching reference point temperatures to the Actual means you have to deal with many variables such as: greater evaporation; heat gains generated by cultures growing - (slowly at first and much more during their growth phase) and heat generated by the friction of media with the glass at high speeds or use of baffled flasks. Over time, the reference point temperature offset may need to change due to these varying conditions.

I want to grow my cultures at 27°C, do I need an incubated shaker with refrigeration?

The Eppendorf Incubated, non-refrigerated Shakers Innova and I-Series are designed to maintain temperatures of ambient plus 5 °C to its maximum operating temperature. The Eppendorf Incubated Excella shakers will operate from ambient plus 7 °C to maximum temperature. It is critical to understand that "ambient temperature is not the temperature on the wall thermometer (room temperature), but the temperature measured one meter from the front of the machine.

Why are some flask clamps supplied with an extra spring set?

This "extra spring set" (we call it a girdle) is included with clamps for 2 L, 2.8 L, 4 L and 6 L flasks. It is intended to be used with the already installed spring set. This girdle helps prevent large flasks from spinning inside the clamp and reduces the risk of flasks becoming dislodged or scored by the steel clamp. One girdle is already in place on the clamp, the other is packed separately. To install this extra “girdle”, follow the instructions in the manual supplied with the shaker.

How is temperature accuracy defined by Eppendorf?

Accuracy is defined as the degree of closeness between the displayed value and the actual value as determined by a traceable device. All Eppendorf Incubated Innova and I-Series shakers have a temperature Accuracy of ±0.1 °C from 30 – 40 °C, ±0.5 °C over the remaining range. New Brunswick Incubated Excella Shakers are accurate within 0.1°C at 37°C.

How is Uniformity defined by Eppendorf?

Uniformity is the ability to maintain uniform temepratures throughout the platform. New Brunswick Incubated Innova Shaker temperatures will not deviate by more than +/- 0.25 °C at 37 °C.

The orbit of a shaker is the distance traveled around the central drive. This can be descibed in inches, centimeters, or milimeters. If our shakers had a one inch (2.54 cm) orbit. That means that that the lateral movement of the platform would equal one inch from one point to another that is 180° opposite that position. All of the New Brunswick. shakers have a circular orbit

What wavelengths are used in your growth lamps in a photosynthetic light bank?

Each of the bulbs that is fit into our photobanks is a wide spectrum bulb that provides the red and blue wavelength of energy needed for photosynthesis. Innova 42R has six bulbs as the Innova 43R and 44R have nine bulbs. To have this option installed, the shaker needs to have the refrigeration option installed as well.

Which screws will fit to which platform ?

All of Eppendorf Inc. clamps and accessories are packaged with multiple screws to fix them to our universal platforms, included in M1013-0261 clamp screw kit (Stainless steel platform screw #S2117-3050 (10-32 x 5/16 in (7.9mm)), Stainless Steel, Aluminum, and Aluminum and Phenolic (Plastic) #S2116-3051 (10-24 x 5/16 in (7.9 mm)), and Wood #S2116-3101 (10-24 x 5/8 in (15.87mm)).

How can I disinfect, clean, maintain my shaker?

We recommend cleaning the exterior of our units with a damp cloth or any standard household or laboratory cleaner to wipe the surfaces clean. Do not use abrasive or corrosive compounds to clean the instruments as they may damage the unit and void the warranty. It is the responsibility of theuser to carry out the proper decontamination procedures if hazardous materials are spilled on or inside the equipment. Before using any cleaning or decontamination method other than those suggested by the manufacturer, users should contact Eppendorf Inc. to ensure that the proposed method will not damage the equipment. Commercially available household bleach solutions, when diluted at a 1:10 ratio, are effective in routine decontamination of the instrument. The method for decontaminating a spill depends on the nature of the spill. Spills involving fresh cultures or samples of known concentrations of biomass should be flooded with decontamination solution and soaked for at least 5 minutes before cleanup. Spills involving samples with high concentrations of biomass, or involving organic matter, or occuring in areeas warmer than ambient/room temperature, should be exposed to decontamination solution for at least one hour before being cleaned up. Personnel involved in the cleanup of any spill should wear gloves, safety glasses, and a laboratory coat or gown during the cleanup process. Respiratory protection should be considered for spills where aerosolization is suspected.

Which flask type fits in which clamp ?

Please see the Accessories for New Brunswick™ Shakers: Dimensions and Capacities in the Userguides section of the shaker product page.

Which vessel fits in Eppendorf Test tube racks ?

Please see the Accessories for New Brunswick™ Shakers: Dimensions and Capacities in the Userguides section of the shaker product page.

Is it possible to monitor relative humidity in the Innova 42, 43, 44? ?

Innova 42, 43, 44 can be equipped with a relative humidity sensor optionally (Humidity monitor). This option allows monitoring the actual humidity level in the chamber and indicates the value on the screen. The option does not allow humidity control. The humidity sensor can be retrofitted by Eppendorf Technical Service. If humidity monitoring is installed, the maximum temperature is 60 °C. The maximum reachable relative humidity is around 40 – 45 % rH (at 37 °C) by filling the spill pan.

Why is the triple eccentric drive special ? What is the difference between Innova and Excella Shakers drive ?

The Innova and I-series Triple eccentric drive consists of three individual bearings and eccentric shafts mounted in a triangular fashion for precise uniform circular motion at every point on the platform. The heavy duty drive has a single shaft that utilizes springs to aid in balancing the load. This drive works great with small to medium loads at lower speeds.

How can I shake MTPs ? Which parameters ?

Eppendorf shakers offer a variety of Micro Titer Plate holders that attach to our univeral platforms. Our shakers offer a variety of orbits up to 5.1 cm (2 in) and speeds up to 500 rpm. If mixing is what is needed at higher speeds and smaller orbits you can find Eppendorf Mixers.

How do I use of sticky pads/sticky tape?

Eppendorf Sticky Pads are recommended for use on our sticky pad platform or our sticky pad adapter kit (M1250-9504). On the S44i universal platform sticky pad can be used directly. The adapter kit is easily fixed to our universal platforms. Any size flask can be used with the sticky pad with a 1 in (2.54 cm) orbit up to 250 rpm, any size flask can be used with the 2 in (5.1 cm) orbit up to 200 rpm. To clean the sticky pad, just wash with soap and water. this will revive" the stickiness, but the sticky pad must be completely dry before replacing on the platform.

What is the heavy load platform ?

The Heavy Duty Platform (M1282-9928) is designed for use in the Innova 44 only. This platform is 0.95 cm thick alluminum plate that is recommended for shaking full loads of flasks greater than 1 L at or above 20 % fill volumes or flasks with baffles.

What is the orbit of a shaker?

An orbital shaker moves the platform in a circular shaking motion. The term orbit describes the diameter of this circular movement. Typical orbit sizes are 1.9 cm, 2.5 and 5 cm.

What orbit shall I take?

An orbital shaker is used to grow microorganisms or cells growing in suspension, like bacteria, yeast, fungal, insect, algae or plant cells. Orbital shaking enables a homogeneous distribution and aeration of the cultures by increasing the oxygen transfer rate (OTR). There are different influencing parameters on shaking performance, e.g. the shaker orbit, the applied speed, the vessel shape, the liquid viscosity and the filling volume. The 2.5 mm orbit is the standard solution which works well for most applications. For some applications, e.g. large vessels > 2 Liter, especially large volume Fernbach flasks or very shear sensitive cells, a larger shaking diameter with the consequence of a reduced speed can be beneficial.

I use two shakers with different orbits. Can I transfer my experimental conditions to a shaker with a different orbit?

Yes, the rpm can be adapted with help of the following formula .

What platform types are offered with the shakers?

Universal platform and a variety of dedicated platforms are available. University platforms offer maximum flexibility having a hole-pattern that allows using virtually any combination of clamps and other accessories. Dedicated platforms come complete with pre-installed clamps of one size. The hole-pattern of the dedicated platform is optimized for the use of one specific size of clamps. It allows in most cased more capacity but can only be used with that size of clamp. Please note that the platform has to be ordered in addition to the shaker.

为什么要定期维护轨道摇床？

对于有可移动部件的所有产品，磨损总是难以避免的，并且可能长时间影响产品操作一致性。 Eppendorf 产品在设计上可以最大程度减轻磨损，然而定期维护可以在产品性能超出可接受容差范围之外前尽早发现和追踪过度磨损。定期维护也可能是用户的一项监管要求。

轨道摇床需要多久维护一次？

Eppendorf 建议每 12 个月进行一次维护。然而，可能与用户的监管要求存在较大差异，后者可能要求进行更频繁的维护。

轨道摇床维护服务价格？

费用取决于产品型号和所需执行的维护水平。请联系您当地的 Eppendorf 客服获取个体化报价。 www.eppendorf.com/contact

IQ 或 OQ 是什么？有什么用？

安装和操作验证；安装验证记录产品已按照制造商规范和指南正确交付和安装。操作验证检查设备是否正常工作，并且符合制造商规范和指南（因此，只能由设备制造商提供该服务）。 IQ/OQ 主要适用于实施质量管理流程的机构，但也适用于所有用户。

text.skipToContent text.skipToNavigation

CN | CNY

未找到任何结果

搜索建议

产品系列

Show all Product Families ()

文章

Show all Articles ()

内容

Show all Content ()

New Brunswick Innova^® 43/43R - 控制台式生物摇床

产品信息

您是否正在寻找一款可以处理大型培养瓶的大容量控制台式生物摇床？敬请查看Innova 43。它配备著名的重型Innova三偏心轴平衡驱动，为您提供全天候安心服务。无需每年更换内部HEPA过滤器以获得最佳性能，它还能在十年内为您节约高达3800美元/3200欧元。

显示更多产品信息

Click to customize and configure your universal platform accessories

索取演示版

您可以在以下网址找到其他下载资料本页面底部

产品 (3)

Services (18)

附件 (13)

备件 (3)

3 产品

New Brunswick™ Innova^® 43 生物摇床

non-stackable, 230 V ± 10 %/50 Hz (CN/EU), 轨道 5.1 cm (2″)

更多产品详情...

数量

库存状态

目录编号 M1320-0012

价格

¥ 288,230.00

查询

New Brunswick™ Innova ^®43R 生物摇床

冷冻型, non-stackable, 230 V ± 10 %/50 Hz (CN/EU), 轨道 2.5 cm (1″)

更多产品详情...

数量

库存状态

目录编号 M1320-0006

价格

¥ 319,462.00

查询

New Brunswick™ Innova ^®43R 生物摇床

冷冻型, non-stackable, 230 V ± 10 %/50 Hz (CN/EU), 轨道 5.1 cm (2″)

更多产品详情...

数量

库存状态

目录编号 M1320-0016

价格

¥ 319,462.00

查询

显示更多产品

已添加到您的购物车

产品信息

技术数据

特征

Innova 43 生物摇床和 Innova 43R 生物摇床（带制冷）控制精确、使用便利，是处理大容量培养的理想之选。采用顶部加载设计，可以垂直取放锥形瓶。脚踏开盖以及可以随时观察样品的侧窗正是客户为什么始终信任我们的设计的例证。铸铁结构的 New Brunswick 三偏心轴平衡驱动专为高转速、高承载应用设计 – 这种设计已经过超过 70 年的考验，今天仍然服务着全世界的科研人员。通过用户界面可以方便地对速度、温度和时间进行编程，还可以添加 VisioNize box 来增强监测以及其他通知功能。可以原位进行定期维护，尽可能缩短停机时间。

使用VisioNize^® Lab Suite

对实验室和设备进行高效管理
您是否想监控自己的实验室设备并接收通知，比如设备警报？数码连接的实验室甚至提供更多。.

能够使用数码服务的模块范围和选择实验室的操作。. VisioNize Lab Suite 为你提供实验室管理人员或科学家所需要的一切，开启实验室数码管理，提高样品的安全性，合规性需求和维护管理。.
定制您自己的优选数码实验室吧! 了解更多

阅读更少

规格	Innova^® 43，轨道直径 5.1 cm（2 英寸）	Innova^® 43R，轨道直径 2.5 cm（1 英寸）	Innova^® 43R，轨道直径 5.1 cm（2 英寸）

外部高度（盖/门打开）	165.1  cm	165.1  cm	165.1  cm
定时器	0.01–99.59 小时，可连续运行	0.01–99.59 小时，可连续运行	0.01–99.59 小时，可连续运行
电源	230 V ± 10 %, 50 Hz	230 V ± 10 %, 50 Hz	230 V ± 10 %, 50 Hz
尺寸（长x宽x高）	115.6 × 81.3 × 103.1 cm / 45.5 × 20 × 40.6 in	115.6 × 81.3 × 103.1 cm / 45.5 × 20 × 40.6 in	115.6 × 81.3 × 103.1 cm / 45.5 × 20 × 40.6 in
产品重量	202 kg / 445 lb	216 kg / 475 lb	216 kg / 475 lb
温度范围	环境温度+10 °C至80 °C	环境温度以下20 °C至80 °C	环境温度以下20 °C至80 °C
声光报警	是	是	是
温度均一性	±0.25°C，37°C 时 °C	±0.25°C，37°C 时 °C	±0.25°C，37°C 时 °C
可用程序模式	• 持续转速和温度控制 • 多步骤编程控制 • RS-232 通讯端口	• 持续转速和温度控制 • 多步骤编程控制 • RS-232 通讯端口	• 持续转速和温度控制 • 多步骤编程控制 • RS-232 通讯端口
驱动装置	三偏心轴平衡驱动	三偏心轴平衡驱动	三偏心轴平衡驱动
台上 (B)，台下 (U)，落地 (F) 或叠放 (S)	F	F	F
通气管	是	是	是
水/湿度监测	是	是	是
内部便捷灯	是	是	是
存储卡	断电后重启自动运行记录参数设置	断电后重启自动运行记录参数设置	断电后重启自动运行记录参数设置
马达类型	固态无碳刷马达	固态无碳刷马达	固态无碳刷马达
光照组件照明	否	是	是
摇床板尺寸	76 × 46 cm (30 × 18 in)	76 × 46 cm (30 × 18 in)	76 × 46 cm (30 × 18 in)
冷冻型	−	是	是
滑出式摇床板	否	否	否
正在打开门	控制台类型	控制台类型	控制台类型
速度范围	轨道偏心距为 2.5 cm 时，25–500 rpm；轨道偏心距为 5.1 cm 时，25–300	轨道偏心距为 2.5 cm 时，25–500 rpm；轨道偏心距为 5.1 cm 时，25–300	轨道偏心距为 2.5 cm 时，25–500 rpm；轨道偏心距为 5.1 cm 时，25–300
多步骤编程	是	是	是
每个程序的步骤	15	15	15
存储的程序	4	4	4
cETLus 和 CE 标志	是	是	是
紫外灭菌灯	−	是	是
容量	大型	大型	大型
编程步骤/可存储程序	15/4	15/4	15/4
远程设备监视和通知 (VisioNize^®)	VisioNize^®框已启用	VisioNize^®框已启用	VisioNize^®框已启用
温度范围	环境温度以上10 °C至80 °C	环境温度以下20 °C至80 °C	环境温度以下20 °C至80 °C

搅拌
轨道	5.1 cm (2″)	2.5 cm (1″)	5.1 cm (2″)