What is the meaning of the red knob on the rotor lid?

A fixed-angle rotor with a red knob on the rotor lid indicates aerosol-tightness.

How did you manage to make the device so quiet?

The Centrifuge 5418 has an inner centrifuge lid which reduces the noise emission to a low level.

Which material is the inner centrifuge lid made of?

The inner lid of the Centrifuge 5418 is made of high-quality V2A stainless steel.

Can the Centrifuge 5418/ 5418 R be opened in case of a power failure?

Yes, the device has an emergency lid release. Before opening the centrifuge, pull the power plug and wait until the rotor stops spinning. The centrifuge 5418 has an emergency lid release via a cord that is located on the underside of the device in the base plate. Remove the white plastic cap and pull the cord downwards. The centrifuge 5418 R has an emergency lid release behind a plastic cover on the right side of the device. Rotate the plastic cover counterclockwise and remove it. Enter the centrifuge rotor key into the hexagonal opening at rear until some resistance can be felt. Slightly press and turn the rotor key counterclockwise.

How can the Centrifuge 5418/5418R be cleaned?

The Centrifuge 5418/5418 R can be cleaned with neutral detergents. For disinfection, we recommend alcohol or alcoholic disinfectants. Make sure that the relevant legal requirements and directives are observed when choosing the disinfection method. A detailed description can be found in the operating manual, which can be downloaded from our website.

What is the minimum selectable rotational speed of the Centrifuge 5418/5418 R?

The minimum selectable speed is 100 rpm. This is equivalent to an rcf of approx. 1 x g.

In which increments can the rotational speed/g-force be adjusted?

The rotational speed can be adjusted in increments of 100 rpm, the g-force (rcf) can be adjusted in increments of 100 x g.

In which increments can the time be adjusted?

In the centrifuge 5418, for a run time up to 10 min the increments are 0.5 min steps, after that it is set in increments of 1 min up to 9:59 h. The function for continuous run mode can be found above 9:59 h and below 0.5 min The symbol "oo" is displayed to indicate the continuous run. In the centrifuge 5418 R, for a run time up to 10 min the increments are 0.5 min steps, after that it is set in increments of 1 min up to 99 min. The function for continuous run mode can be found above 99 min and below 0.5 min. The symbol "oo" is displayed to indicate the continuous run.

My Centrifuge 5418 displays "EP". What does that mean?

"EP" is displayed when the automatic standby function is active. It is not an error code. If the centrifuge remains unused for more than 15 min., the standby function is activated, indicated by "EP" on the display. By using any key or knob or closing the centrifuge lid, the centrifuge is re-activated and ready to use. The letters "EP" were chosen because a lot of Eppendorf products already have this prefix in their name.

Can the fixed-angle rotor FA-45-18-11 be operated without a rotor lid?

The fixed-angle rotor FA-45-18-11 can be used with or without rotor lid. With rotor lid the centrifugation is aerosol-tight and the Centrifuge 5418/5418 R is even quieter. The aerosol-tight centrifugation can only be carried out with the rotor lid. Especially when working with pathogenic microorganisms, we recommend the usage of the aerosol-tight lid. When centrifuging filter devices like spin columns or other comparable tubes, the aerosol-tight rotor lid must be used in any case. This protects the centrifuge from damage – e. g. by torn-off tube lids.

Which material is the fixed-angle rotor for tubes made of?

The fixed-angle rotor is made of massive, anodized aluminum. This material is durable and has got a good chemical resistance. The rotor lid is made of the same material.

Can the sealing of the aerosol-tight rotor FA-45-18-11 be exchanged?

The sealing of the aerosol-tight rotor FA-45-18-11 can very easily be exchanged. A detailed description with illustrations can be found in the operating manual, which can be downloaded from our website.

Which tubes can be used in the Centrifuge 5418/5418 R?

1.5 ml and 2.0 ml Eppendorf ® tubes can be spun in the Centrifuge 5418/5418 R. With the help of adapters, the centrifugation of 0.2 ml PCR tubes, 0.6 ml Microtainer, 0.5 ml and 0.4 ml micro tubes is also possible. Even so-called spin columns (e.g. Quiagen, Macherey-Nagel, Vivascience) can be centrifuged. For centrifugation of spin columns, the rotor lid must be used.

For which applications can I use the Centrifuge 5418/ 5418 R?

The rotor of the Centrifuge 5418/5418 R allows a broad variety of applications. Up to 18 micro test tubes can be centrifuged at 16,873 x g. It can be used with tubes from 0.2 up to 2.0 ml. The potential applications include: - Isolation of DNA, RNA and proteins - Spin columns - Aerosol-tight centrifugation of infectious samples - Pelletizing of cells (bacteria, eukaryotic cells) up to 2.0 ml - Spinning down of PCR mixtures in tubes

In which rotors can I centrifuge 0.2 mL PCR tubes?

0.2 mL PCR tubes can be used in the rotor FA-45-18-11 using an adapter (Order No. International 5425 715.005; North America 022636260).

In which rotors can I centrifuge 0.5 mL micro test tubes?

0.5 mL micro test tubes can be centrifuged in the rotor FA-45-18-11 using an adapter (Order No. International 5425 716.001; North America 022636227).

How do I recognize aerosol-tight rotors?

Firstly, the aerosol-tight rotors can be recognized by their designation abbreviation “FA”, where the letter “A” indicates the aerosol tightness; secondly, we have color-coded the aerosol-tight rotors. All aerosol-tight rotors now have a red rotor lid screw, and a red ring is printed on to the rotor shaft.

Why are the standard rotors in the micro centrifuges 5418, 5418 R, 5424, 5424 R, 5430, and 5430 R aerosol-tight?

At Eppendorf, the safety of the user always has the highest priority. That is why we now fit our centrifuges with aerosol-tight rotors as standard – at no extra charge.

When does the opening of the centrifuge lid take place automatically or manually?

Following the end of a centrifuge run, only the lid of the Centrifuge 5418 is automatically opened in order to provide quicker access to the sample and to avoid potential heat accumulation. The Centrifuge 5418 R is not equipped with the automatic opening of the centrifuge lid. In order to maintain a consistent temperature in the rotor chamber and in the sample, the centrifuge lid for this device must always be manually opened by pressing the "open" key.

Can the Centrifuge 5418/5418 R be operated in the cooling room at 4° C?

The Centrifuge 5418 can be operated at an ambient temperature in the range from 2° C to 40° C. Operation in the cooling room at a temperature of 4° C is therefore possible. The permitted range of the ambient temperature is between 15 °C and 35 °C for the Centrifuge 5418 R, so that this centrifuge could not be operated in a cooling room at 4 °C.

What is "Fast Temp" (Centrifuge 5418 R)?

The "Fast Temp" function is a temperature control run of the Centrifuge 5418 R without samples and with a rotor and temperature-specific rotational speed in order to quickly bring the rotor chamber, incl. the rotor, buckets and adapters, to the set nominal temperature. In order that the samples can be centrifuged from the beginning on at the desired temperature, one starts this temperature control run during sample preparation by pressing the "Fast Temp" key. The display shows the current temperature and g force (rcf) or speed (rpm) as well as “FT” as symbol for a “Fast Temp” temperature run. You can find a more detailed description in the operating manual of the Centrifuge 5418/5418 R.

For the 5418 R, when does the continuous cooling of the rotor chamber start?

The continuous cooling starts with each rotor standstill of the Centrifuge 5418 R in order to maintain the preselected nominal temperature of the rotor chamber not only during centrifugation. To this purpose the following prerequisites must be met: - The centrifuge is switched on. - The centrifuge lid is closed. - The nominal temperature is lower than the ambient temperature. Continuous cooling is ended by opening the centrifuge lid.

What is the lowest temperature that can be reached with the Centrifuge 5418 R?

The lowest temperature of the Centrifuge 5418 R is 0 °C. The device is thereby optimized with the rotor in such a way that at least 4 °C is maintained at the maximum speed.

What is the temperature range of the Centrifuge 5418 R?

With the Centrifuge 5418 R it is possible to set the temperature within a range from 0 °C to +40 °C.

Does the Centrifuge 5418 R has an energy saving function?

Yes, the ECO shut-off automatically switchs off the compressor after 8 hours of non-use.

How can the speed display be switched from rotational speed (rpm) to relative centrifugal force (rcf, g-force)?

The display is switched back and forth between rpm and rcf by pressing the "rpm/rcf" key.

Does the lid latch have to be serviced or greased at regular intervals?

No, in order to ensure the full functionality of the lid latch, it must not be cleaned or greased. If you feel that this is nevertheless necessary, please contact our Technical Service. The contact address can be found in the operating manual of your centrifuge.

For what applications are aerosol-tight rotors important?

Aerosol-tight rotors are always recommended or even prescribed when working with hazardous or potentially hazardous substances. These can, for example, be viruses, pathogenic bacteria, potentially infectious blood samples or radioactive sample material.

Why are the standard rotors in the micro centrifuges 5418 R, 5420, 5424 R, 5425, 5427 R, 5430 and 5430 R aerosol-tight?

At Eppendorf, the safety of the user always has the highest priority. That is why we now fit our centrifuges with aerosol-tight rotors as standard – at no extra charge.

text.skipToContent text.skipToNavigation

AR | ARS

No se han encontrado resultados

Sugerencias de búsqueda

Familias de Productos

Show all Product Families ()

Artículo

Show all Articles ()

Contenido

Show all Content ()

Centrifuge 5418 R

Centrifuge Rotor FA-45-18-11 – QuickLock® mechanism

Soft-touch lid closure on the microcentrifuge Centrifuge 5418 R

Eppendorf microcentrifuge Rotor FA-45-18-11 for Centrifuge 5418 R with lid

Información del producto

La Centrifuge 5418 R es una microcentrífuga de 18 posiciones que está diseñada específicamente para una capacidad baja o media en tubos de 1,5/2,0 mL y Microtainer^®. La velocidad de hasta 16.873 × g permite realizar aplicaciones estándar de biología molecular.

Mostrar más información del producto

Solicite una demostración

Encontrará material adicional para descargar en laparte inferior de esta página

Sets y packs (3)

Services (8)

Rotores (1)

Accesorios (1)

3 Sets y packs

Centrifuge 5418 R

botones giratorios , refrigerada, con rotor FA-45-18-11 y tapa de rotor
230 V/50 – 60 Hz (EU)

Más detalles del producto ...

N.^o de catálogo 5401000010

Centrifuge 5418 R

botones giratorios , refrigerada, con Rotor FA-45-18-11 y tapa de rotor
230 V/50 – 60 Hz (AR)

Más detalles del producto ...

N.^o de catálogo 5401000056

Centrifuge 5418 R

botones giratorios , refrigerada, con Rotor FA-45-18-11 y tapa de rotor
120 V/50 – 60 Hz (South America/TW)

Más detalles del producto ...

N.^o de catálogo 5401000021

Mostrar más productos

Añadido a su carro de la compra

Información del producto

Datos técnicos

Características

El rotor refrigerado Centrifuge 5418 R con sus 18 posiciones de capacidad está diseñado específicamente para una capacidad mediana y baja en tubos de 1,5/2,0 mL y Microtainer^®. Su velocidad de hasta 16.873 × g permite realizar aplicaciones de biología molecular estándar. Además, este equipo compacto tiene una altura de acceso especialmente baja y se caracteriza por un funcionamiento notablemente silencioso.

Tapa

Eppendorf QuickLock^® para un manejo ergonómico

Rotor de centrífuga con tapa QuickLock única para un cierre de tapa rápido y seguro realizando sólo un cuarto de vuelta. El rotor proporciona una contención hermética a los aerosoles que permite el centrifugado seguro de muestras peligrosas como virus, bacterias patógenas, muestras de sangre o sondas radioactivas.

¿Orgulloso propietario de un producto Eppendorf? ¿Ya lo ha registrado?

¿Sabía que si registra su producto Eppendorf con nosotros obtendrá lo siguiente?
• 100 epPoints^® (por cada producto que registre) para canjear en nuestra tienda de premios
• Garantía adicional de 3 meses al registrar una centrífuga, un agitador, un incubador de CO2 o un termociclador
• Participación en un sorteo exclusivo de Eppendorf (por cada producto que registre)
• Haga que su historia personal sobre el producto se publique en el sitio web de Eppendorf

¡Empezar es súper fácil! O bien
1. Descargue la Eppendorf App, escanee y regístrese o
2. Visite nuestra página web, inicie sesión en su cuenta myEppendorf e introduzca el número de serie del producto
Más información en:www.eppendorf.com/productregistration

Final de la vida útil

Eliminación del embalaje
El embalaje de la centrífuga contiene diferentes materiales y puede incluir una paleta de madera, cartón, una cubierta de plástico antipolvo y algunas piezas de espuma. El reciclaje de materiales es cada vez más importante: ¿Sabía que casi todo el material de cartón se recicla en Europa? Nuestro material de cartón para el embalaje de la centrífuga consiste en un 50% de material reciclado. Le rogamos que apoye la iniciativa de sostenibilidad mundial de reciclaje de materias primas recogiendo también el material de embalaje de cartón del equipo y eliminándolo en el contenedor de recogida apropiado en sus instalaciones. Con respecto a la cubierta de plástico antipolvo hecha de LD-PE y las piezas de espuma, recomendamos elegir a un socio de reciclaje dedicado donde el material de PE pueda ser reciclado. Le recomendamos ponerse en contacto con su transportista de residuos local o con el equipo de gestión de las instalaciones para conocer las opciones de reciclado que tiene su organización.

Eliminación del equipo
Nuestras centrífugas duran muchos años pero, si hay que sustituirlas, le pedimos que cumpla los requisitos locales de eliminación de estos equipos. Recomendamos encarecidamente un socio de reciclaje local debidamente certificado con experiencia en dispositivos con refrigeración activa. Mantenerlo todo «local» reduce el impacto del transporte, y se recomienda el aspecto «certificado» debido a la extracción y el reciclado seguros y sostenibles de los líquidos de refrigeración, si se trata de una centrífuga refrigerada.

Descontaminación
Este equipo se ha utilizado en un laboratorio o se ha usado para manipular muestras biológicas. Recuerde que debe descontaminar de forma adecuada el equipo que se debe desechar. Consulte los requisitos locales. Para obtener más información, póngase en contacto con su responsable de bioseguridad o responsable de desechos. Compruebe si su empresa de reciclado local tiene instrucciones especiales o requisitos de documentación. También puede usar el formulario de descontaminación de Eppendorf como orientación.

Leer menos

Características	5418 R

Máx. FCR	16873 × g
Máx. FCR con rotor de ángulo fijo	16873 × g
Velocidad	100 – 14.000 rpm (100 rpm pasos)
Tipo de producto	Centrífugas
Rotores disponibles	1
Máx. capacidad	18 × 1,5/2,0 mL
Tiempo de aceleración¹⁾	13 s
Tiempo de deceleración¹⁾	13 s
Temporizador	30 s a 9:59 h, con función de marcha permanente
Nivel de ruido	< 57 dB(A)
Alimentación eléctrica	230 V, 50 – 60 Hz
Máx. consumo de energía	320 W
Dimensiones (An × Pr × Al)	30 × 46 × 25 cm / 11,7 × 18,23 × 9,8 in
Peso del producto	22 kg / 48,5 lb
Altura (con tapa abierta)	52 cm / 20 in
Enfriamiento	refrigerada
Rango de temperatura	0 °C a +40 °C

1)Los tiempos de aceleración y deceleración pueden variar en función del rotor, la carga y la versión de tensión.

Descargas: Centrifuge 5418 R

Guía de selección

Centrifuge Family Overview

También puede considerar

Benchtop Centrifuge 5810 and 5810 R with mixed loading capability for tubes, bottles, and plates

Centrifuge 5810/ 5810 R

Centrífuga de sobremesa compacta de rendimiento medio a alto

Protein LoBind^® Tubes

Maximice la recuperación de proteína con Protein LoBind^® Tubes

DNA LoBind® tubes - 0.5 mL, 1.5 mL, 2 mL and 5 mL with closed lid

Eppendorf Safe-Lock Tubes

Eppis: los EppendorfSafe-Lock Tubes ofrecen una protección especial contra la apertura involuntaria y eliminan por completo cualquier riesgo de fugas durante la incubación y el almacenaje

Está a punto de abandonar este sitio.

Centrifuge 5418 R

The Centrifuge 5418 R with OptiBowl® design

Centrifuge Rotor FA-45-18-11 – QuickLock® mechanism

Soft-touch lid closure on the microcentrifuge Centrifuge 5418 R