Why should I have my ep Motion serviced at regular intervals?

To ensure the optimum performance and precision of your device. This also enables the early detection of any defects which can then be corrected easily. Only precise and accurate devices ensure successful liquid transfers!

How often does my ep Motion need to be serviced?

The need for service depends on how intensively the device is used and if you are working in a regulated field with special service demands. However, we recommend to have it serviced at least once a year.

What do you need to look out for before carrying out a service?

The device needs to be decontaminated first. The device must be freely accessible and all samples removed from the device.

What types of service programs are available for ep Motion ?

The available service programs can be found under the respective instrument in the Service & Support / Maintenance and Certification Services section.

Why do the dispensing tools of my ep Motion need to be calibrated?

The dispensing tools are precision devices. Servicing and calibration at regular intervals ensure a consistently high precision of the results. We provide documentation in support for GLP to assist you.

How often do dispensing tools need to be calibrated?

As part of his test equipment monitoring process, the operator determines the frequency of the calibration as well as the quantity of the testing volume and the number of measurements for each testing volume. This may vary depending on how often the device is used, by how many operators it is used, the aggressivity of the liquids used and the maximum permissible errors defined by the operator. The dispensing tools of your device will display after 200,000 runs that an inspection is recommended. However, there should be at least 1 calibration per year.

How much are the different ep Motion service programs?

The costs depend on the model and service that is performed. Please contact your local Eppendorf Service.

Who is my local service contact?

Please contact your local Eppendorf Service Team. You find the contact data on our homepage ( www.eppendorf.com ) or in the information materials.

What is IQ or OQ and what do I need them for?

Installation and operational qualification; the IQ documents that the device has been delivered and installed correctly. The OQ checks the correct functioning of a device. IQ/OQ ensure that your quality management requirements are met and that your device operates properly and in accordance with the manufacturer’s specifications.

How often does the OQ need to be carried out for an ep Motion ?

The company is responsible for technical checks of devices. Eppendorf recommends regular device qualifications depending on the intensity of use, however, they should be carried out at least once a year.

Does a service carried out by Eppendorf meet the GMP requirement?

Eppendorf offers global certification services which comply with FDA 21 CFR Part 11, EU GMP Annex 11, GLP and GAMP ® 5 to ensure a consistent, standardized operation. We also enable an uncomplicated validation from the implementation to the shutdown by providing support for the installation und operational qualifications (IQ/OQ) of the device and with the software. The entire qualification is documented in detail and the operator’s personnel is qualified and certified in intensive training sessions.

Which consumables should be replaced at regular intervals?

All three XYZ flex cables should be replaced at least once per year if the machine is used daily.

What types of training or online training do you offer to enable me to improve my skills?

Please visit the Eppendorf webpage about the Eppendorf Training Center ( https://www.eppendorf.com/training or contact your local Eppendorf Service for further information and a quotation.

Why can the dispending tool be calibrated without the user unit ?

The ep Motion dispensing tool is calibrated with the help of the ep Motion Tool Holder. The electronic parameter to control the tools of the ep Motion are always the same in all ep Motion units. Therefore all ep Motion dispensing tool can be calibrated on different units than the user unit. The only exceptions are the TS10 and TM10 dispensing tool. They can only be calibrated with units controlled by epBlue Version 40.5.

text.skipToContent text.skipToNavigation

PL | PLN

No results found

Search Suggestions

Product Families

Show all Product Families ()

Article

Show all Articles ()

Content

Show all Content ()

epT.I.P.S.^® Motion as SafeRack tips

Product Information

The new epMotion systems can reuse tips as e.g. economical choice for multiple wash steps of the same well. Here special epT.I.P.S. Motion SafeRack tips are recommended

Show more Product Information

You will find additional download material at the bottom of this page

Product Information

Applications

Features

Automated pipetting processes place high demands on the design and material of pipette tips used. Eppendorf has specially designed the epT.I.P.S. for use on the epMotion^® 5070 & 5075 Liquid Handling Workstation. epT.I.P.S. Motion SafeRack pipette tips, with and without filters, developed in torsion-resistant, contamination-free racks that are recommended for the re-use of tips feature of epMotion 5073 systems.

Reuse Tips Feature

The new epMotion systems can reuse tips as e.g. economical choice for multiple wash steps
of the same well. Here special epT.I.P.S. Motion SafeRack tips are recommended. Pipette tips
will be placed back into the position of the box they were removed from. Returned tips will
be reused within an application for the same source vessel.

• Individual compartments in rack to avoid cross-contamination between used tips
• Available as standard and PCR clean quality for 50, 300 and 1000 µL